1. Introduction

Spallation process is a key reaction, which creates spallation neutrons in target material irradiated by charged particles. In the first stage, the primary incident particle reacts with nucleons-neutrons and protons-inside the nucleus. The reactions that follow create an intranuclear cascade of high-energy (greater than 20 MeV) protons, neutrons, and pions within the nucleus. During the intranuclear cascade, some of these energetic hadrons escape as secondary particles. Others deposit their kinetic energy in the nucleus leaving it in an excited state. In the second stage (nuclear de-excitation), evaporation takes place when the excited nucleus relaxes by emitting low-energy (less than 20 MeV) neutrons, protons, alpha particles, etc., with the majority of the particles being neutrons. The low-energy neutrons produced during nuclear de-excitation are important in a spallation source because they can be moderated (reduced) to even lower energies for use as research probes. After evaporation, the nucleus that remains may be radioactive and may emit gamma rays ^[1].

Different target materials could be used as spallation target which heavier targets are considered as the best. The uranium target could have some attractions as a neutron source than conventional lead-bismuth (PbBi) due to its stunningly higher spallation neutron yield. Many experimental and theoretical studies have been performed on bare uranium spallation target to evaluate its neutron production capability and the mechanism of the spallation process in a wide range of incident proton energy. In the following, some of them will be reviewed.

Ismailov et al.[2] carried out the feasibility study of natural uranium spallation target in order to improve the neutron balance in the accelerator driven system (ADS) of Japan Atomic Energy Agency (JAEA) type to transmute minor actinide (MA). In this respect, the comparative study of uranium target with conventional PbBi both in bare case and in ADS was implemented. In addition, pin type uranium target cooled by PbBi was introduced aiming at enhancing the spallation target properties such as neutron generation efficiency and operation temperature. They used MCNPX 2.7.c to determine neutronics of the modeled spallation target. First, they studied bare cylindrical spallation target without a blanket. The neutron yield in depending on target size was investigated for determining the optimal conditions of the effective neutron source. They optimized the target length at fixed proton beam energy equal to 1.5 GeV with beam radius of 1 cm. Their results showed the irradiated optimized-dimension target could produce about 65 n/p.

Hashemi-Nezad et al. (2008) studied experimental target set up made of four cylindrical lead targets each with diameter 8.4 cm and length 11.4 cm which a natural uranium blanket surrounds each of the four target sections. Each uranium blanket is composed of 30 uranium rods of diameter 3.6 cm (including the Al-cladding) and length 10.4 cm hermetically sealed in aluminum cladding. The uranium rods are arranged in the form of hexagonal (triangular) lattice with the pitch size of 3.6 cm. The weight of natural uranium in each blanket section is 51.6 kg and whole setup contains a total of 206.4 kg of natural uranium. In this work, they used MCNPX 2.6.c to study neutronic performance of the irradiated target and the target size was fixed at constant for each proton beam energy, while in the proton energy higher than 1.5 GeV the optimal target length should be longer than 50 for uranium target. The radius of the proton beam was kept constant at 1 cm, and the neutron yield at proton energies in range starting from 500 MeV up to 2 GeV was simulated with the used code. Their results show that proton-, pion- and photon-induced fissions contribute significantly to the total fission rate in the samples within the target volume and its immediate vicinity while about 97% of fissions come from (n,f). Another obtained result from them indicates the code prediction of the fission rate is consistently lower by 22±0.14% than the experimental value for the fission-foils placed in the blanket region, when Bertini and RAL models are used in the calculations. This deviation reduces to 13±0.09% when the Bertini and ABLA models or CEM03 model are used instead ^[3].

Hashemi-Nezad et al. (2011) investigated variation of the escaping, captured and total neutron yield as a function of the target radius in irradiation of range-long targets of ^natW, ^natPb, ²³²Th and ²³⁸U with 1.0 GeV protons. They used MCNPX 2.7.c code to study the selected targets. Their result showed a 10 cm radius presents that peak of escaped neutron yield and the target radius enhancement more than 10 cm is not efficient ^[4].

Sahin et al. (2015) demonstrated that the heavier target nucleus and the higher incident proton energy resulted in a greater number of neutrons would emanate from the target nucleus so that thorium and uranium targets will generate more neutrons than lead and bismuth. Their study analyses the integral ²³³U and ²³⁹Pu breeding rates, neutron multiplication ratio through (n,xn)- and fission-reactions, heat release, energy multiplication and consequently the energy gain factor in infinite size thorium and uranium as breeder material in an accelerator driven systems (ADS), irradiated by a 1-GeV proton source ^[5].

Literatures show such evaluations have started from the 1970s, some experiments were carried out on uranium target to study the spallation process inside it as well as its neutronic behavior. The following review illustrates them briefly.

Russell et al. (1980) irradiated depleted uranium target by 800-MeV to understand proton spallation reactions which are important to the spallation neutron source development ^[6]. Vasilkov et al. (1978) investigated neutron multiplication in massive metal uranium targets bombarded by 300, 400, 500 and 660 MeV protons. The total mass of every rectangular target with dimension of 56×56×64 cm was 3.5 ton ^[7].

Whereas, the uranium spallation target is of interests because of its high neutron yield, investigation of neutronic parameters of natural uranium target irradiated using different proton energies was proposed in this work.

2. Material and methods

MCNPX 2.6.0 code ^[8] was used to model the spallation process in a cylindrical natural uranium target. To investigate the effect of proton energy enhancement on fission rate growth inside the spallation target, a fixed dimension of 10×10 cm was chosen for the cylindrical target and 30, 50, 70 and 90 MeV proton energies were used to induce spallation in the modeled target separately.

As the de Broglie wavelength of the incident proton is around a nucleon dimension (~ 1.7 fm), it interacts with individual nucleons in the target nucleus (instead of creating a compound nucleus). The projectile shares its kinetic energy with target nucleons by elastic collisions and a cascade of nucleon-nucleon collisions proceeds. However it is said Intra Nuclear Cascade (INC) is more probable for proton energies of >100 MeV but its occurrence is probable for low energies also ^[9].

According to the following equation, the de Broglie wavelength ^[10] of a 30 MeV incident proton is ~ 5.22 fm.

Where ħ•c=197.32 (MeV.fm), proton rest mass is 938 MeV and Ep is incident proton energy. It should be mentioned that uranium target diameter is 15.49 fm. Hence, an INC can be applied reasonably well to study the systematics of the propagation of nucleons at low energies of a few tens of MeV ^[11]. Therefore, a 30 MeV proton could interact with a uranium target by Intra Nuclear Cascade (INC).

First, the cylindrical target dimension was optimized at the selected proton energies. An optimized radius was chosen so that there is not more than ~ 5% enhancement in escaped neutron yield from the spallation target when it is getting bulkier. A void sphere was considered around the cylindrical target and the escaped neutrons were tallied over the spherical surface. The same procedure was used to determine an optimized target length of the fixed-radius target at any incident proton energy. Neutron spectra leaked from the optimized-dimension spallation target was determined for any proposed projectile energy. Different physical models of MCNPX code, including Bertini/Drenser, Bertini/Abla, Isabel/Drenser, Isabel/Abla, INCL4/Drenser, INCL4/Abla and CEM was used to calculate neutron yield, deposited energy and mass distribution of different isotopes, which are producing inside the modeled optimized-dimension uranium spallation target. An obtained relative discrepancy between the results using different physical models was discussed.

The modeled targets irradiated by proton beam with a current of 100 μA (5 mm spatial FWHM), respectively. Many particles (2000000) were transported to reduce the calculation errors to less than 0.4%. The ²³⁹Pu production rate in any optimized target was discussed. Fission per absorption ratio was determined for any optimized spallation target.

Water coolant was proposed to cool the 30 MeV proton-induced one with a specific velocity. The target temperature profile was obtained using FLUENT code. Impacts of high-energy proton projectile on leaked neutron yield and deposited heat inside the uranium target with a fixed dimension was discussed.

ENDF/B-VI continuous-energy cross sections were used for the calculations. Target temperature enhancement effects on the escaped neutron yield, the deposited heat and the leaked neutron flux from the optimized-dimension target was determined using TMP card and temperature-related cross section libraries of .70c, and.71c from endf70 library of the used code.

Delay gammas weights on the escaped neutron yield were ignored for the low-energy investigations. It is mandatory for high-energy applications and could be applied by the ACT card ability of MCNPX2.7 code.

To determine neutron spectra in latter surface of the spallation system, F1 tally can be employed which each time a particle crosses the specified surface, its weight is added to the tally, and the sum of the weights is reported as the F1 tally in the MCNP output ^[12].

In the energy range, where nuclear data tables are available, the neutron, photon, and proton energy deposition is determined using the heating numbers from the nuclear data tables. These heating numbers are estimates of the energy deposited per unit track length. In addition, the dE/dx ionization contribution for electrons and/or protons is added for MODE E or MODE H.

Above the tabular energy limits, or when no tabular data is available, energy deposition is determined by adding different factors. For charged particles, ionization (dE/dx) energy is deposited uniformly along the track length (which is an important factor, when creating mesh tallies). All other energy depositions are calculated at the time of a nuclear interaction. The energy of secondary particles, if they are not to be tracked (i.e., not included on the MODE card) will be deposited at the point of the interaction. Nuclear recoil energy will be deposited at the point of interaction too, unless heavy ion transport is specified. In order to obtain the most accurate energy deposition tallies, the user must contemplate or consider all potential secondary particles on the MODE card. PEDEP card can be used to calculate energy deposition ^[8]. The tally computes the energy deposition using equation 3 ^[13]:

Where ρ_a is atom density (atoms/barn-cm), ρ_g is gram density (grams/cm3) and H(E) is heating response (added over nuclides in a material). F6 tally for Neutrons is calculated via:

Which

and

σT= total neutron cross section,

E = incident neutron energy,

Pi(E) = probability of reaction i,

E_out= average exiting neutron energy for reaction i,

Qi = Q-value of reaction i,

Eγi= average energy of exiting gammas for reaction i.

F6 tally for Photons is calculated via the following equations:

i= 1 incoherent (Compton) scattering with form factors

i= 2 pair production

i= 3 photoelectric ^[13].

RES card of MCNPX is used to calculate residual nuclei inside the irradiated spallation target ^[8].

3. Results and discussion

Neutron yield and deposited heat were calculated in the modeled uranium spallation target. At first stage, a 10 cm fixed height was considered for the target and an optimized target radius was determined. The calculations showed that for the target irradiated by 30 MeV protons, a 5 cm radius is adequate whereas the target radius enhancement will not increase the escaped neutron yield more than 5%. Therefore, a fixed 5 cm radius was used for the target and its efficient height was determined. The results display after 10 cm height, the target elongation does not improve the obtained neutron yield significantly. Hence, the optimized cylindrical target dimension at proton irradiation of 30 MeV was selected as 10×10 cm (Fig.1).

Fig. 1.Full-screen View

Neutron spallation yield dependence on a) radius b) height, proton energy: 30 MeV

The same procedure was followed to determine an optimized target dimension for irradiations by 50, 70 and 90 MeV protons. The computational results showed a 10×10 cm dimension is the best for irradiation by 50 MeV protons and bigger dimensions not only don’t increase the leaked neutron yield more than 5% but also more massive uranium spallation targets are in less interest due to higher residual nuclei production and thermo-hydraulic point of views (Fig.2).

Fig. 2.Full-screen View

Neutron spallation yield dependence on a) radius b) height, proton energy: 50 MeV

According to Figs.3-4, the best dimension for 70 and 90 MeV irradiations was chosen 8×10 cm.

Fig. 3.Full-screen View

Neutron spallation yield dependence on a) radius b) height, proton energy: 70 MeV

Fig. 4.Full-screen View

Neutron spallation yield dependence on a) radius b) height, proton energy: 90 MeV

Default physical model (Bertini/Drenser) of MCNPX code was used for pervious calculations. At the next stage, the impact of the code available physical models on such calculations for the optimized dimensions will be discussed. By using two LCA and LEA cards, the different physical models could be applied (Table 1).

Relative discrepancy of neutron yield and deposited heat values calculated by different INC physical models of MCNPX code was investigated at the proposed proton energy. The results indicated at 30 MeV proton energy there is not significant relative discrepancy (< 4% on average) between neutron yield values calculated by the INCL4 and Bertini models. About 19% relative discrepancy is seen between Isabel/Drenser and CEM model. In case of heat deposition inside the modeled target is seen an average relative discrepancy of <0.035% occurs between INC models which uses Drenser de-excitation models. A similar behavior is seen in the obtained data from Abla de-excitation model. CEM presents a heating value close to INC models with Abla de-excitation model. In case of the heating value calculation, about 0.7% relative discrepancy is seen between INCL4/Drenser (maximum) and INCL4/Abla (minimum) (Fig.5).

Fig. 5.Full-screen View

a) Neutron spallation yield b) deposited heat dependence on different INC physical models, proton energy: 30 MeV

Projectile energy enhancement resulted in average higher discrepancies of spallation neutron yield and deposited heat values (0.04-5.3% and 3.16-23% respectively correspond to 30 and 90 MeV proton energy) obtained by different physical models (Figs. 6, 7 and 8).

Fig. 6.Full-screen View

A) Neutron spallation yield b) deposited heat dependence on different INC physical models, proton energy: 50 MeV

Fig. 7.Full-screen View

A) Neutron spallation yield b) deposited heat dependence on different INC physical models, proton energy: 70 MeV

Fig. 8.Full-screen View

A) Neutron spallation yield b) deposited heat dependence on different INC physical models, proton energy: 90 MeV

The CEM model presented the highest neutron yield values at all investigated projectile energies while Isabel/Drenser resulted in the least values. Overall, the MCNPX code allows the user to choose between different intra-nuclear cascade and fission-evaporation model combinations among Isabel, Bertini and INCL4 for cascade and Drenser (associated with RAL or ORNL fission models) and Abla for de-excitation. Whereas most portion of neutron yield is related to INC stage, Isabel/Abla and Isabel/Drenser models showed close neutron yield values at all the investigated proton energies. The same behavior is seen about Bertini and INCL4 models. In case of the deposited heat, which is mainly related to the fission-evaporation stage, Drenser model data are close to each other. The same behavior is seen in the case of Abla model at all investigated projectile energies. As it is observed of Figs.6, 7 and 8, Drenser model resulted in the highest deposited heat values.

Different researches show that INCL4/Abla or Isabel/Abla physics models can obtain very reasonable predictions of spallation-fission products in uranium target ^[14,15]. Hence, CEM/ INCL4/Abla and Isabel/Abla models were used to calculate the mass distribution of the produced isotopes inside the irradiated uranium target. Two options of RES card and histp proficiency of the used computational code could be applied to calculate mass distribution of the produced residual nuclei inside the irradiated target. If histp proficiency is used for the mentioned aim, the constructed file should be converted to a readable file by HTAPE3X.exe and IOPT 8 option.

The computational data showed CEM model data are underestimated in fission section of the mass distribution curve than the INCL4 and Isabel models. In addition, these two models present fitter data with each other (Fig.9).

Fig. 9.Full-screen View

a) Residual nuclei distribution, proton energy: 30 MeV b) Residual nuclei distribution, Isabel/Abla model

As it is seen in Fg.9-b, proton energy enhancement increases residual nuclei yield. For instance, the produced yield of A=135 becomes 3.13 times by proton energy enhancement of 30 MeV to 50 MeV. Nevertheless, the yield growth is happening slower between 50 to 70 MeV and 70 to 90 MeV (1.90 and 1.60 times respectively).

Calculation of neutron spectra leaked from the bare spallation targets show 30 MeV proton injection with current of 100µA through the modeled uranium target produces a neutron flux in order of 10⁷ n/s.cm². Using 50 MeV projectiles, the neutron flux becomes ~ 65 times in comparison with 30 MeV proton projectiles. According to Fig.10, higher energy projectiles do not increase the leaked neutron flux noticeably (3.85 and 2.85 times correspond to 70 MeV and 90 MeV energy respectively).

Fig. 10.Full-screen View

a) Neutron spectra leaked from the optimized bare spallation targets using different proton energies, Isabel/Abla model

According to Table 2, the bare investigated spallation targets produce about 70% neutrons with an energy range of 10 keV to 2 MeV. Irradiation of the targets by 100 µA proton current produces a thermal power of 3.03-9.67 kW depended on the energy of an injected proton. Calculations showed the investigated targets produce 3.12-3.30 neutron per fission during irradiation. Malyshkin et al. (2014) investigated the number of neutrons per fission in an 8×12 cm cylindrical ^natU target exposed by 600 MeV protons. They used Geant4-based code MCADS for this calculation. Their obtained value (2.74) has about 14% relative discrepancy with our data ^[18]. The natural uranium target experiences high fission per absorption ratio obviously, because a hard neutron spectrum is available inside the spallation target and proton-fission reaction rate increases the fission rate. Application of higher proton energies will not increase the ratio because the peak of proton-fission cross sections in natural uranium target happens around 50 MeV (Fig.11).

Fig. 11.Full-screen View

Proton-fission and neutron-fission cross sections in ²³⁸U target, Library: JENDL/HE2007.

As it is seen in Fig.12, application of higher proton energy has the advantage of higher neutron yield productions from other reactions except fission. This noticeably higher (p,nx) cross sections in comparison with fission at high proton energies eliminates the uranium target overheating and raises the neutron yield of the used spallation target.

Fig. 12.Full-screen View

Proton-fission and proton-nx cross sections in ²³⁸U target, Library: JENDL/HE2007.

Argonne research center used ²³⁸U target material irradiated by 450 MeV protons with 15 µA current. They used eight discs of the mentioned material and the designed spallation target bears 8 kW of thermal power. Light water was used as coolant of the spallation target. The coolant flow was 0.45 m/s and its outlet temperature was less than 85 ˚C. In addition, 304 SS was used as target housing vessel and the hydraulic pressure differential across the target assembly is 1.0 bar, 15 psi ^[16].

At Rutherford Appleton Laboratory, 800 MeV protons with a ~100 µA current induce the spallation process in a uranium target ^[17].

Calculations of this work show the hottest section of the modeled targets is the proton beam entrance adjacent segments (because the Bragg peak of 30 MeV protons is occurring near to this location). According to Fig. 13, upper surface of the cylindrical target irradiated by 30 MeV protons with 100 µA current bears the most heat deposition. The target cooling by light water with a flow of 0.6 m/s will results in maximum temperature of 95 ˚C near to beam entry (Fig.14).

Fig. 13.Full-screen View

Temperature profile of the irradiated uranium target, proton energy: 30 MeV, current: 100 µA.

Fig. 14.Full-screen View

Temperature distribution inside the irradiated uranium target a) axial b) radial (z=0.09, the hottest plane)

The obtained calculations showed the target surface temperature remains under boiling temperature of water coolant to avoid the coolant boiling. Higher temperatures are experienced by internal sections, but the target surface keeps the temperature limitations.

Temperature-related cross sections were used for the optimized spallation target exposed of 30 MeV protons. The obtained results showed the escaped neutron yield of the modeled bare target decreased less than 0.02% at higher temperature (598 K). However, resonance broadening is happening for the natural uranium target because of temperature enhancement, but the inexistence of thermal and epithermal neutrons inside the modeled spallation target causes an approximately unchanged outgoing neutron flux. When water coolant covers the target, the mentioned value decreased less than 0.5%. In sum up, temperature enhancement decreases the neutron flux around the spallation target somehow.

In MCNPX, net neutron production is tallied implicitly and is provided by default in the problem summary for neutrons. The problem summary shows net neutron production resulting from nuclear interactions (the component that accounts for neutron production by all particles transported using INC/Pre-equilibrium/Evaporation physics) and net production by (n,xn) reactions (neutrons created in inelastic nuclear interactions by neutrons below the transition energy, using evaluated nuclear data) ^[8]. Fraction of any reaction inside the optimized uranium target irradiated by 30 MeV protons is presented at Table 3. As is seen, the produced neutrons by the INC, fast neutron fission, proton-fission and (n,nx) are not depended on water coolant presence or neutron spectra softening as a result of the moderating role of the used coolant. Obviously, neutron-fission rate increases using the coolant because the number of neutrons with E_n<2 MeV increases.

Water coolant application increased the neutron flux leaked from the investigated target with a factor of 2.3.

Clearly higher proton energies or currents produces higher deposited heat inside the uranium spallation targets, so that water could not be used as an adequate coolant at atmosphere pressure.

Higher leaked spallation neutron fluxes using low energy proton projectiles is accessible using higher currents meanwhile this increases deposited heat inside the uranium targets. In contrast, irradiation of uranium target using high-energy proton could noticeably increase the neutron flux without much heating of the target. According to Fig.15, application of 250 MeV proton energy increases the leaked spallation neutron yield up to 130 times, than the one produced by 30 MeV protons. Meanwhile the deposited heat becomes 10 times than the investigated 30 MeV energy.

Fig. 15.Full-screen View

High-energy proton impacts on leaked neutron yield and deposited heat, uranium target dimension: 5×50 cm a) direct values b) multiplied values in comparison with the target irradiated by 30 MeV

However absorption cross sections of natural uranium target in fast and epithermal neutron energy is noticeably higher than other costmary spallation targets such as lead, lead-bismuth, mercury tungsten, but its high fission cross sections compensates the drawback by creating a neutron yield of 3-4 times in comparison with the other targets using the same projectile energy and target dimension.

Overall, an accelerator-based neutron source produces pulsed neutron beams, which could be cost effective in comparison with high efficiency reactor-based neutron sources that produce steady higher flux neutron beams. However, an accelerator-based one produces pulsed lower flux neutron beams, but proliferation resistance issues and safety operation that comes with nuclear reactors makes a growing interest on construction of accelerator-based neutron sources. In addition, these accelerator-based neutron sources have low background between pulses and thereby good signal to noise. Electron particles could be applied to generate neutrons in a heavy target by (γ,n) reactions. Nevertheless, only very high-energy electrons could produce suitable neutron yield and it is reported a 100 MeV e- on ²³⁸U produces a neutron flux in order of 3.1× 10¹⁵ n/MW While 800 MeV p on ²³⁸U could produce a neutron flux in order of 1.1× 10¹⁷ n/MW ^[19,20,21]. In case of our investigated neutron source, the produced neutron flux is in order of ~ 10⁹ n/MW using injection of 30 MeV proton beam of 100 µA current in the optimized natural uranium target.

In addition, other low-energy accelerator-based methods were investigated to produce an external neutron source. Miyamaru et al. (2008) evaluated the neutron emission profile of the ⁹Be(d,n)¹⁰B nuclear reaction using a low-energy deuteron beam (300 keV) to develop an accelerator neutron source. Their results show the system is able to produce a neutron flux in order of 10¹⁰ n/s.cm² in the utilized heavy water moderator using 50 mA current. Therefore, the source produces ~ 66× 10¹⁰ n/MW ^[22].

Capoulat et al. (2013) reported the medical application of a neutron field produced by bombarding a thin Be target (8μm) with a 30 mA beam of 1.45 MeV deuterons ^[23].

Inada et al. (1968) measured the energy and angular distributions as well as the yields of fast neutrons from a thick Be-disk bombarded by 1.0 MeV to 3.0 MeV deuterons. Their obtained results showed about 5.6×10⁵ n/MW could be available using 2.3 MeV deuterons induced on Be target ^[24].

Logan et al. (1977) designed a compact beryllium target which produces a neutron flux of about 6× 10⁷ n/MW (E> 1 MeV) when bombarded with 20µA of 30 MeV deuterons ^[25].

Overall, the study shows good potential of the 30 MeV proton cyclotrons (CYCLONE30) for production of an external neutron source with acceptable intensity for many research aims. Nevertheless, the calculations carried out based on the estimation of the threshold energy for spallation induction on ^natU target, which meets the rough estimation of particle wavelength and nuclear radius. It should be noted that the assurance for accurate application of the INC model for such low-energy calculations needs benchmarked or experimentally validations.

A few experimental and benchmark studies have been done to determine validity of INC models at low projectile energies. Thanks for David valuable study (2015), which focused on a review of spallation reactions as a successful interplay between modeling and applications. The work reported a comparison of INCL4.5 and INCL4.6 predictions for the neutron double differential cross-sections in p(63MeV) + Pb collisions which shows a good conformity with experimental data. In addition, the model is in good conventionality in the case of ⁹Be(d, xn) for 18MeV projectile. Another investigation on p(175 MeV) +Ni reported by David indicates both Isabel and INCL4.5 plus Abla de-excitation models present acceptable agreements with the experimental. As the data reported by David, mass distributions of the nuclide production given by INCL4 and Isabel models for the reaction ⁵⁶Fe (300A · MeV)+p have good agreements with the available experimental ^[26].

Another work carried out by Blann et al. (1993) shows there is about 7% relative discrepancy between neutron multiplication calculated by Bertini+ Pre-equilibrium model and the experimental data of p(80 MeV)+Pb, and about 15% relative discrepancy is between the other presented multiplications and Isabel+ Pre-equilibrium model. In addition, at that time they reported there is room for improvement in all codes, and that modeling calculations on a predictive basis may have uncertainties of the order of ±50% ^[27]. However, the available INC models of the different computational codes improved much until now, but there maybe are many blanks to validate utilization of such codes for low-energy INC calculations.

4. Conclusion

Spallation targets can be applied to produce an external source of neutrons, which are wildly used for radioisotope production, neutron radiography or neutron therapy. Computational codes could efficiently be used to predict neutronic and thermal hydraulic performance of a spallation target. The present study illustrates there is not noticeable relative discrepancy between different physical models for calculation of spallation neutron yield and deposited heat values in uranium target irradiated by 30-90 MeV protons. Light water at 1 atm pressure could easily cool the 10×10 cm cylindrical uranium target irradiated by 30 MeV protons of 100 µA current. The spallation target produces a leaked neutron flux in order of 10⁷ n/s.cm². Obviously higher neutron fluxes using low energy protons could be obtained by higher proton current registration inside the spallation target, but it would increase the deposited power. The mentioned problem confronts the system to metal coolant need or light water coolant usage at higher pressures. However, higher proton energies seems to be more capable to induce the spallation process in uranium targets, but shielding challenges of such neutron source systems should be considered as major concerns.