Development of a 7-cell S-band standing-wave RF-deflecting cavity for Tsinghua Thomson scattering X-ray source

ACCELERATOR, RAY TECHNOLOGY AND APPLICATIONS

Development of a 7-cell S-band standing-wave RF-deflecting cavity for Tsinghua Thomson scattering X-ray source

Xian-Cai Lin，

Hao Zha，

Jia-Ru Shi ，

Liu-Yuan Zhou，

Shuang Liu，

Jian Gao，

Huai-Bi Chen

Nuclear Science and Techniques

Vol.32, No.4

Article number 36

Published in print 01 Apr 2021

Available online 10 Apr 2021

DOI：10.1007/s41365-021-00871-5

54200

A 2856-MHz, π-mode, 7-cell standing-wave-deflecting cavity was designed and fabricated for bunch-length measurement in Tsinghua Thomson scattering X-ray source (TTX) facility. This cavity was installed in the TTX and provided a deflecting voltage of 4.2 MV with an input power of 2.5 MW. Bunch-length diagnoses of electron beams with energies up to 39 MeV have been performed. In this article, the RF design of the cavity using HFSS, fabrication, and RF test processes are reviewed. High-power operation with accelerated beams and calibration of the deflecting voltage are also presented.

Deflecting RF cavityStanding waveBunch length measurementThomson X-ray source.

1 Introduction

The Tsinghua Thomson scattering X-ray source (TTX) was used as a tunable monochromatic X-ray source for advanced X-ray imaging experiments [1]. A photocathode RF electron gun provided 3-ps, 3.5-MeV Gaussian bunches, which were further accelerated to 50 MeV and compressed to 1 ps before interacting with the laser. During the experiments, it was crucial to diagnose the spatial and energy distribution of the bunch. A longitudinal distribution measuring system based on a 3-cell deflecting cavity has been designed previously [2]. Recently, an upgrade plan to boost the beam energy with X-band high gradient structures [3] and provide greater than 5-MV deflecting voltage with 4-MW power input was proposed, and a 7-cell standing-wave-deflecting cavity (SDC) was developed and fabricated to provide a higher deflecting voltage and better measurement accuracy.

When the deflecting cavity operates, the electron bunches enter the cavity center at zero phase. A deflecting force, approximately linear to the longitudinal location, acts on the bunch. As a result, the longitudinal distribution of the bunch is converted to a transverse distribution on the screen after drifting some distance. From the perspective of beam transmission, the bunch undergoes a linear shear transformation in the system. Therefore, the RF deflecting cavity provides a direct method to measure the bunch length, as well as high resolution.

In recent years, many deflecting cavities for bunch-length measurement have been designed and fabricated, including traveling-wave-deflecting structures (TDSs) and SDCs. Various deflecting structures have been reported, such as L-band TDS at PITZ [4]; L-band SDC for the Cornell ERL injector [5]; S-band TDS at SLAC (LOLA IV [6, 7]) and IHEP [8, 9]; S-band SDC at FERMI SPARC [10], Tsinghua University [11], and Waseda University [12]; C-band TDS at Spring 8 for X-FEL (RAIDEN [13, 14]) and at PSI for SwissFEL [15]; C-band SDC at Tsinghua University [16, 17]; X-band TDS at SLAC for LCLS [18, 19], at Shanghai for SXFEL [20, 21], and at PSI for SwissFEL (PolariX TDS [22, 23]); and X-band SDC at UCLA[24]. Generally, a higher operation frequency can provide better measurement accuracy. In our design, a frequency of 2856 MHz was chosen based on the existing RF system in TTX. Although TDSs can provide a stronger deflecting voltage, an SDC is selected because it is more compact and efficient. Increasing the cell number could enhance the deflecting ability of the cavity; we chose 7 to provide a targeted deflecting voltage.

This paper presents an intact process for designing and testing a 7-cell SDC. The theory of SDCs is reviewed, and a simple and quick method is used to optimize a multicell SDC working in π mode. The influence of the end-cell length on the transverse shunt impedance is also explored. RF tests after fabrication are shown, including the unloaded Q values, external Q values, and field distribution. Finally, high-power operation with accelerated beams and calibration, as well as their underlying principles, are demonstrated.

2 Basic properties of SDCs for bunch-length measurement

From the perspective of how the microwave propagates inside the cavity, deflecting cavities are divided into traveling- and standing-wave structures. Both have advantages and disadvantages. For traveling-wave structures, there is negligible power reflection from the structure, and the structure can be stacked until very long. A formula can be used to estimate the deflecting voltage $V_{def}$ versus input power $P_{0}$ and structure length $L$ for the S-band disk-loaded traveling structure [7].

V_{def} \approx (1.6 MV / m / {MW}^{1 / 2}) L \sqrt{P_{0}}

(1)

For standing-wave structures, because the microwave is trapped and coherently stacked inside the cavity, less power is needed to yield the same field level as that of the traveling-wave structure. A similar formula can be concluded from Ref. [11] for an S-band disk-loaded standing-wave structure.

V_{def} \approx (4.3 MV / m^{1 / 2} / {MW}^{1 / 2}) \sqrt{L P_{0}}

(2)

The disadvantage of the standing-wave structure is that power is reflected during the filling process, and a circulator is needed to direct this power to the load to avoid influencing the power source. Furthermore, to avoid mode aggregation, the standing-wave structure cannot be too long. According to the upgrade plan to provide more than 5 MV of deflecting voltage with a 4-MW input, the shortest structure lengths using Eq. (1) and Eq. (2) are 1.6 m and 0.34 m for traveling- and standing-wave structures, respectively. The latter is only one-fifth that of the former. Considering the existing room for the TTX beamline and moderate input power for the deflecting cavity, a standing-wave structure was adopted.

The SDC operates in the TM110-like mode. For an ideal cylindrical cavity, there is only a transverse magnetic field along the z axis. In this study, we set the direction of the transverse magnetic field as the x axis. With this convention, the charged particles moving along the z axis suffer a deflecting force in the y direction. Owing to the beam tunnel at a realistic cavity for charged particles to go through as well as coupling between cells, there is an $E_{y}$ component in the z axis to satisfy the boundary condition. The field distribution in a single cell operating in the TM110-like mode is shown in Fig. 1. For a particle moving at a velocity near the speed of light, its momentum change approximately equals the energy change divided by c, i.e., $Δ p = \int^{} F d t \approx \int^{} F d z / c = e V / c$ . Therefore, the voltage is used to describe the momentum change. The transverse voltage can be calculated as the integration of the electric and magnetic fields along z axis, as shown in Eq. (3).

Fig. 1.

Magnetic and electric field of a single cell in a standing-wave cavity

V_{y} (φ) = Re {\int^{​} [{\tilde{E}}_{y} (z) e^{j k z} + η {\tilde{H}}_{x} (z) e^{j k z}] e^{j φ} d z},

(3)

where $φ$ is the phase of the microwave when the particle arrives at z = 0. ${\tilde{E}}_{y}$ and ${\tilde{H}}_{x}$ are the complex electric and magnetic fields, respectively, and $η$ is the free-space wave impedance. $Re{ }$ represents the real components. The concept of deflecting voltage is used to describe the maximum transverse voltage a charged particle can gain, which can be calculated as

V_{def} = max {V_{y} (φ)} = | \int^{​} [{\tilde{E}}_{y} (z) e^{j k z} + η {\tilde{H}}_{x} (z) e^{j k z}] d z |,

(4)

where $| |$ represents the magnitude of the enclosed value. For the standing wave, ${\tilde{E}}_{y}$ and ${\tilde{H}}_{x}$ have a 90° difference in phase. Therefore, an appropriate phase can be selected to yield ${\tilde{E}}_{y} = Re{{\tilde{E}}_{y}}$ , ${\tilde{H}}_{x} = j \cdot Im{{\tilde{H}}_{x}}$ . It is noted that the results from simulation software, such as HFSS, have this form. Considering the symmetry of fields in a single cell (z = 0 is set at the middle of the cell), $\int^{} Re{{\tilde{E}}_{y}} \cos k z d z = \int^{} Im{{\tilde{H}}_{x}} \sin k z d z = 0$ , where $k$ is the wavenumber of the microwave. Therefore, Eq. (4) can be simplified for a standing-wave cavity as Eq. (5).

V_{def} = \int^{​} [Re{{\tilde{E}}_{y}} \sin k z + η \cdot Im{{\tilde{H}}_{x}} \cos k z d z] d z

(5)

Equation (3) could also be simplified using Eq. (5) for a standing-wave cavity:

V_{y} (φ) = Re {\int^{​} j V_{def} e^{j φ} d z} = - V_{def} \sin φ,

(6)

It should be noted that Eq. (5) could be simplified further with the Panofsky–Wenzel theorem by integrating longitudinal electric field off z axis [2], but Eq. (5) could provide more physical information. For example, the calculation using the data shown in Fig. 1 with Eq. (5) shows that both the magnetic and electric fields attributed to the deflecting voltage accounted for 64% and 36%, respectively.

For deflecting cavities used to measure bunch lengths, the center of the bunch experiences zero transverse voltage, which means that the bunch center arrives at the cavity center at phase $φ = 0$ . Therefore, a charged particle at a distance $Δ z$ from the center would arrive at the cavity center at a phase $φ = - k Δ z$ . Its transverse voltage can be calculated by

V_{y} (Δ z) = V_{def} \sin k Δ z \approx V_{def} k Δ z,

(7)

which shows that a force approximately linear to the longitudinal location of the particle is applied to the bunch. The deflecting voltage represents the ability to transform the longitudinal location of the bunch to the transverse location. The original 3-cell deflecting cavity at TTX can provide a 3.4-MV deflecting voltage with a 4-MW input [2]. The goal of the upgrade plan is to increase the deflecting voltage to 5 MV. According to the definition of transverse shunt impedance,

R_{⊥} = \frac{V_{def}^{2}}{P},

(8)

the deflecting voltage can be expressed with input power and transverse shunt impedance per meter, as shown in Eq. (9).

V_{def} = \sqrt{P \cdot R_{⊥}} = \sqrt{P \cdot R_{⊥} / L \cdot L}

(9)

This is also the derivation of Eq. (2). Because $R_{⊥} / L$ remains almost the same with different cell numbers for identical cell shapes, the deflecting voltage with the same input power is nearly proportional to the square root of the cell number. In our design, this number is chosen to be 7 to provide an approximately 5.2-MV deflecting voltage with an input power of 4 MW.

3 RF design of 7-cell SDC

The cavity shape is a disk-loaded structure. The polarization degenerated mode of the TM110 mode is separated by a pair of cylindrical slots on the sidewall of the cells. The magnitudes of the electric and magnetic fields of the working mode and degenerated polarized mode at the xy plane (z = 0) are shown in Fig. 2. In this figure, (a) and (b) show that the polarization of the working mode is on the y axis, while the degenerated mode is at the x axis. (c) and (d) show that the working mode has little field at the slot, while the degenerated mode has a comparatively strong magnetic field at it. According to perturbation theory, the existence of slots reduces the frequency of the degenerated mode, while it has little influence on the working mode. The frequencies of these two modes versus the slot radius are shown in Fig. 2 (e). The center of the slot was located at the side faces of the cavity. A quadratic function is appropriate for describing the relationship because the frequency perturbation amount is nearly proportional to the perturbation volume. In our model, the slot radius is 5 mm, and the frequency of degenerated mode is 6.5 MHz lower than the working mode, which is larger than the frequency bandwidth of the working mode and variation of the microwave power source and therefore adequate for operation. It should be noted that slots do not need to be set at the center cell because the power coupler can separate the degenerated mode.

Fig. 2

(Color online) (a) Electric field amplitude of the working mode at xy plane; (b) electric field amplitude of the degenerated polarized mode; (c) magnetic field amplitude of the working mode; (d) magnetic field amplitude of the degenerated polarized mode; (e) frequency of the working mode and the polarized degenerated polarized mode versus slot radius. The center of the slot is located at the side faces of the cavity.

The design goal of an SDC is to settle its eigenmode frequency and optimize its magnetic field distribution along the z axis, as the magnetic field provides a major part of the deflecting voltage. The radius of each cell was adjusted to achieve this goal. For an n-cell cavity, this is an n-dimensional optimization problem. The symmetry of the cavity means that cells can be divided into three types: the center cell with the coupler, the inner cells, and the end cells with beam tunnels, corresponding to part $11$ – $33$ in Fig. 3. Therefore, this n-dimensional problem is simplified to a 3-dimension one. Furthermore, because the cavity works in the π mode, each cell can be separated as a single cavity with a perfect H boundary (the transverse magnetic field is zero) at the intersection plane. The optimization of each type of cell can be performed individually to make them work at the designed frequency. After combining these three parts, only a precise adjustment was needed to generate a flat field distribution. The parameters of the cavity after optimization are listed in Table 1, where $a$ is the radius of the beam pipe as well as the iris, $b_{i}$ is the radius of each cell, $d_{i}$ is the cell length, and $t$ is the thickness of the disk, as shown in Fig. 3. The subscript i is the index of the cells, numbered 1–7 from left to right.

Parameters of the 7-cell deflecting cavity

Parameter	Value (mm)	Parameter	Value (mm)
a	17.5	t	10
b₁, b₇	61.48	d1, d₇	45
b₂, b₃, b₅, b₆	61.23	d₂-d₆	52.52
b₄	60.74

Fig. 3

(Color online) 3D model of the 7-cell deflecting cavity in HFSS

The RF power was fed into the cavity with a BJ-32 (or WR-284) waveguide through a coupling slot. The coupling factor of the cavity was set to 1.1, with the experience that the $Q_{0}$ value after fabrication was approximately 85% the simulated value[25]. According to the definition, the coupling factor was set to 1.1 × 7 in the isolated center cell model. The calculation and optimization process was accomplished using high-frequency simulation software [26]. Two methods were utilized: the modal solution, where power is fed from the waveguide and the coupling factor is calculated from the S11 parameter; and the eigenmode solution, where the absorption material is placed at the end of the waveguide. The relative difference between the two solutions is less than 1 × 10^-3, whereas the latter requires less CPU time. The RF parameters of the cavity are listed in Table 2. The final size of the coupling slot was 28.66 × 10.00 mm². An identical slot was placed at the other side of the center cell for pumping, as well as for symmetry, as shown in Fig. 3.

Simulation results of the 7-cell deflecting cavity

Parameter	Value	Parameter	Value
f (MHz)	2856.00	Q₀	1.61 × 10⁵
Coupling factor	1.08	E_peak/V_def(m^-1)	9
R_⊥(MΩ)	7.4	(R/Q₀)_⊥(Ω)	460

The wideband frequency response of the cavity calculated in the HFSS, as well as the identification of modes, is shown in Fig. 4. Because the power is fed through the middle cell, only the symmetric mode, i.e., π mode, 2π/3 mode, π/3 mode, and 0 mode, is activated. The magnetic field patterns at the yz plane (x = 0) are also plotted in Fig. 4. The nonsymmetric modes of this cavity, i.e., the 5π/6, π/2, and π/6 modes, are suppressed. The nearest mode, 2π/3 mode, is 13 MHz from the working mode, which is adequate for practical operation.

Fig. 4

(Color online) S11 curve of the 7-cell deflecting cavity and magnetic field plot of different modes at yz plane (x = 0).

Owing to the large apertures of the deflecting cavity, there was obvious field leakage in the end cells. In other words, there was a long tail at the end of the cavity in the magnetic field distribution along the z axis. This could be compensated by shrinking the iris at the two ends. However, considering that the bunch’s transverse size became larger after deflection, this idea was abandoned. Instead, shortening the length of the cells at the two ends was adopted. To study the influence of end-cell length, the transverse shunt impedance and transverse shunt impedance per meter versus end-cell length were calculated in HFSS, as shown in Fig. 5 (a). In each end-cell length case, the cell radius and coupler hole were adjusted to maintain the working frequency, field flatness, and coupling factor. Two cases of end-cell lengths of 45 and 52.52 mm were selected to plot their magnetic field distribution, as shown in Fig. 5 (b). According to Fig. 5 (a) and (b), although the full width at half maximum (FWHM) at the end cell is shortened with decreasing end-cell length, the shunt impedance is decreased. This could be explained by two effects on the shunt impedance when shortening the end-cell length. First, less energy was needed for the end cells, which could lead to higher power allocation in other cells. This led to an increase in the field distribution. Second, the location of $H_{\max}$ at the end cell moved and deviated from its best location to synchronize with the bunch. In other words, when the particle arrived at the location of $H_{\max}$ , the fields in the cavity were not at their maximum moments, which led to a decrease in shunt impedance. The simulation results show that the second effect outweighs the first effect. As a result, shortening the end cell leads to a slight drop in the transverse shunt impedance. However, because of the decrease in length, the shunt impedance per meter increased. As a compromise between the cavity length and deflecting voltage, an end-cell length of 45 mm was chosen, where the shunt impedance per meter was the maximum value.

Fig. 5.

(a) Transverse shunt impedance and transverse shunt impedance per meter versus end-cell length; (b) Comparison of field distribution with 2 different end-cell length case at 52.52 mm and 45 mm.

4 Cavity fabrication and RF measurement

The final CAD model for fabrication is shown in Fig. 6. A series of cells was formed by stacking the bowl cavities. This bowl cavity is similar to the normal cavity as an accelerating structure, except for two cylindrical slots in the x direction for polarized mode separation. Because the bowl cavity is not circularly symmetric, alignment slots were notched outside for assembly. A pair of tuning holes was made for each bowl cavity on the outer wall for tuning after brazing and during operation. Tuning holes were placed in the y direction, where the power coupler was located, because the frequency sensitivity was the largest there. On the center cell, owing to the existence of the power coupler, four tuning holes were placed at an angle from the y axis. The power-feeding waveguide used an SLAC-type female flange, whereas the beam pipe and pumping port used CF-35 flanges. The feedthrough was placed in the vacuum pipe for an RF pickup to measure the signal inside the cavity. Four cooling pipes were welded near the alignment slots. The length of the whole model in the z direction, including beam pipes and flanges, was 431.35 mm.

Fig. 6

(Color online) CAD model for fabrication

RF measurements were performed before and after the brazing using a vector network analyzer (VNA). The measured results after tuning, as well as the simulated S11 curve, are shown in Fig. 7. The resonant frequency $f_{0}$ was obtained from the reﬂection (S11) curve. The loaded quality factor was calculated as $Q_{l} = f_{0} / Δ f$ , where $Δ f$ is the FWHM cavity energy. More specifically, $Δ f = f_{1} - f_{2}$ , where $1 - S 11 (f_{1}) = 1 - S 11 (f_{2}) = (1 - S 11 (f_{0})) / 2$ . $(1 - S 11)$ represents the cavity loss of the cavity, which is proportional to the energy storage. For a critically coupled cavity, $S 11 (f_{0}) \approx 0$ and $S 11 (f_{1}) = S 11 (f_{2}) \approx - 3 d B$ . A more accurate method to measure quality factor based on reflection curve was introduced in Ref. [27]. The values of $f_{0}$ , $f_{1}$ , and $f_{2}$ are shown in Fig. 7. The coupling factor can be calculated from the reflection coefficient at the resonant frequency. Therefore, the two quality factors, $Q_{0}$ and $Q_{e x t}$ , can be obtained from the S11 curve. The frequency offset due to the circumstance difference of measurement and operation was amended with [11]

Fig. 7.

Measured (solid line) and simulated S11 (dotted line) curve of 7-cell cavity

f (t_{0}) \approx f (t_{1}) \sqrt{ε_{r}} [1 - α (t_{0} - t_{1})],

(10)

where $t_{0}$ is the operation temperature, $t_{1}$ is the environmental temperature of the microwave measurement, $ε_{r}$ is the relative permittivity of air, and $α$ is the linear expansion coefficient of copper. The measurement data before brazing, after tuning compared with the designed value, are shown in Table 3. The $Q_{0}$ value after fabrication was only approximately 2% less than the design value. The comparison of the measured and simulated S11 curves, displayed in Fig. 7, also shows good consistency between the simulation and fabrication.

Frequency, unloaded quality factor, and external quality factor of different stages

	f₀ (MHz)	Q₀	Qext
Designed value in HFSS	2856.00	1.61 × 10⁴	1.49 × 10⁴
Before brazing	2855.03	1.46 × 10⁴	1.58 × 10⁴
After tuning	2856.02	1.59 × 10⁴	1.47 × 10⁴

The field distribution was measured using the bead-pull method, as shown in Fig. 8. The cavity was placed vertically and connected to a vector network analyzer through a coaxial-to-waveguide adapter. The perturbation bead was made from a copper sheet and wound with nylon wires. The motion of the bead was controlled using a stepping motor.

Fig. 8

(Color online) Field distribution measurement platform.

According to the perturbation theorem, the relationship between the frequency perturbation and field amplitude is given by Eq. (11) [16].

Δ f \propto α H_{0}^{2} - β E_{0}^{2},

(11)

where $α$ and $β$ are coefficients determined by the shape of the bead and the material attribute. At the location where the magnetic field reaches its maximum, the electric field is zero. Therefore, the maximum frequency shift represents the maximum magnetic field. Only the relative field magnitude was considered in the test. Owing to the polarization of the working mode, the rotation of the bead changes the coefficients and causes errors in field measurements. A 2-line bead-pull method was proposed in Ref. [16] and used in this experiment to prevent rotation of the bead. The bead was wound with two nylon wires, and a special pulley was fabricated to separate these two lines, as shown in Fig. 8.

After brazing, the frequency was 500 kHz lower than the designed value, and the field distribution was not flat. The frequency and field distribution were tuned simultaneously to avoid repeatedly pushing and pulling the tuning hole. When tuning, pushing the hole of one cell would increase the frequency of the working mode as well as the field in this cell decline. The motion of the bead was controlled using a stepping motor. However, during the tuning process, it was suggested to control it manually and only collect the maximum frequency shift for each cell. This could reduce the time to perform the entire field measurement. The results of the bead-pull measurements before and after tuning are shown in Fig. 9. The frequency change $Δ f$ was normalized to that of the center cells, $Δ f_{0}$ . In the field distribution, there are seven crests above the baseline, which indicate the peak magnetic field in the middle of the cells, and six valleys below the baseline, which indicate the peak electric field at the iris location along the axis. Before tuning, the relative frequency change indicated that the magnetic field varied from 1.0 to 1.5. Because the magnitude of the field is proportional to the square root of the frequency change, the maximum variation of the cell-to-cell magnetic field before tuning was approximately 25%. After tuning, the relative frequency change varied from 0.9 to 1.1, and the maximum variation in the cell-to-cell magnetic field after tuning dropped to approximately 6%.

Fig. 9.

(a) Bead-pull measurement result of the 7-cell deflecting cavity before tuning, (b) bead-pull measurement result of the 7-cell deflecting cavity after tuning

5 High-power operation with accelerated beam

After fabrication and tuning, this deflecting cavity was installed at the TTX beamline. A photograph of the deflecting cavity at the platform is shown in Fig. 10 (a). The layout of the RF system in the TTX is shown in Fig. 10 (b). The entire RF system is fed by a 2856-MHz klystron, which can provide a 2- $μs$ , 40-MW high-power microwave pulse with a repetition rate of 10 Hz. The power from the klystron is first divided by a 5-dB directional coupler. Then, a 13-MW pulse travels to the photocathode RF gun, which is triggered by a laser to provide a 3-MeV high-quality electron beam at its exit. The remaining 27-MW pulse is further divided by a 10-dB directional coupler. A 24-MW pulse travels to the main acceleration section, a 3-meter S-band traveling structure, which can boost the bunch to approximately 50 MeV. The remaining 2.7-MW power goes through a circulator to feed the deflecting cavity. It should be noted that all these power values were calculated without transmission loss. Attenuators, phase shifters, and dry loads are also used to adjust the microwave power, control the microwave phase, and absorb the residual power. Directional couplers are placed before each RF structure to measure the input and output pulses. Before operation, the cavity is subjected to an 18-h conditioning process. The input power of the cavity reached 2.5 MW, which is the maximum value our RF system can provide.

Fig. 10

(Color online) (a) Photo of the deflecting cavity at the platform; (b) RF power feeding system of the TTX. Att. and P.S. stand for attenuator and phase shifter, respectively. The power value was calculated without transmission loss.

As shown in Fig. 10 (b), the electron bunch generated by the photocathode was accelerated by the 3 m structure. Then, the accelerated bunch entered the deflecting cavity. When the deflecting cavity is switched on, a force linear to the offset of the electron, relative to the bunch center, acts on the bunch. The relative momentum change in the y direction can be calculated by Eq. (12).

y^{'} (Δ z) = \frac{Δ p_{y}}{p} \approx \frac{Δ W_{y}}{W} = \frac{e V_{y} (Δ z)}{W} = \frac{k e V_{def}}{W} Δ z,

(12)

where $p$ is the momentum of the bunch, $W$ is the energy of the bunch, and $Δ z$ is the particle’s z location relative to the bunch center. After exiting the deflecting cavity, the bunch drifts for a distance of $D$ before colliding with the screen. The relationship between the y position of a particle at the location of the screen and its original position is

y (s) = y_{0} + y^{'} (s) \cdot D = y_{0} + \frac{k e V_{def} D}{W} s,

(13)

where $s = Δ z$ . For a Gaussian distribution, the relationship between the RMS bunch size with and without the deflecting cavity is expressed as Eq. (14).

σ_{y}^{2} = σ_{y, 0}^{2} + \frac{k e V_{def} D}{W} σ_{s}^{2},

(14)

where $σ_{y, 0}^{}$ and $σ_{y}^{}$ are the transverse bunch sizes in the y direction before and after switching on the deflecting cavity, and $σ_{s}$ is the longitudinal bunch length. Therefore, according to Eq. (14), the bunch length of a Gaussian beam can be calculated using Eq. (15).

σ_{s} = \frac{W}{k e V_{def} D} \sqrt{σ_{y}^{2} - σ_{y, 0}^{2}}

(15)

In this experiment at the TTX beamline, 40-pC bunches emitted from the photocathode cavity were accelerated to 39 MeV, which was measured using a magnetic analyzer. Bunch projections were collected onscreen as the deflecting cavity was switched off and on. When the deflecting cavity was switched off, the bunch had a small transverse size, leaving a small beam spot on the screen, as shown in Fig. 11 (a). The transverse RMS bunch size in the y direction was $σ_{y, 0} = 1.17 mm$ . When the deflecting cavity was switched on, the longitudinal distribution was converted to a transverse distribution, and the beam spot became a long strip, as shown in Fig. 11 (b). The transverse RMS bunch size after deflection in the y direction was $σ_{y} = 5.50 mm$ .

Fig. 11

(Color online) (a) Bunch projection with the deflecting cavity switched off; (b) bunch projection with the deflecting cavity switched on.

Before using Eq. (15) to calculate the longitudinal bunch length, $V_{def}$ must be known or measured, but it can also be calculated using the measured input power and the simulated transverse shunt impedance. In the experiment, it was measured by calibrating the deflecting cavity. The calibration process involves shifting the input microwave phase and measuring the displacement distance of the bunch center. When the phase is offset, the bunch center deviates from its zero-phase location. According to Eq. (6), the deflecting voltage of the bunch center becomes $V_{y} (Δ φ) = - V_{def} \sin Δ φ \approx - V_{def} Δ φ$ , where $Δ φ$ is the phase shift of the input microwave. It should be noted that this is equivalent to offsetting the bunch center at a distance $Δ z = - Δ φ / k$ . The relation between the displacement distance of bunch center and the offset phase is

Δ y = \frac{e V_{y} (Δ φ) D}{W} = - \frac{e V_{def} D}{W} \sin Δ φ \approx - \frac{e V_{def} D}{W} Δ φ,

(16)

where $Δ y$ is the displacement distance of the bunch center, and $Δ φ$ is the offset phase controlled by the phase shifter. The calibration coefficient $e V_{def} D / W$ can be used directly to calculate the longitudinal bunch length using Eq. (15). In our experiment, the calibration coefficient was used to calculate the deflecting voltage and transverse shunt impedance, which were compared with the simulated values.

The projection of the bunches with and without phase offset during calibration is shown in Fig. 12. The blue solid line is the outline of the bunch that enters the deflecting cavity at the zero phase. The green dotted line is the outline of a bunch that enters the cavity at a 1° phase offset. The distance between their bunch center in the y direction is 4.4 mm. Therefore, according to Eq. (16), the calibration coefficient was $e V_{def} D / W = 0.253 m / rad$ . The measured bunch length of the beam $σ_{s}$ in this experiment is 0.354 mm, or 1.18 ps, using this calibration result. The parameters of the measurement condition and calibration results are listed in Table 4. The measured transverse shunt impedance is 7.1 $MΩ / m$ . It should be noted that this is a preliminary experiment using two RF phases. Experiments including more phases and error analyses will be performed in the future.

Bunch-length measurement condition and calibration results

Parameter	Value
Input power, P (MW)	2.5
Electron energy, W (MeV)	39
Drifting length, D (m)	2.35
Calibration coefficient, eV_defD/W (m/rad)	0.253
Deflecting voltage, V_def (MV)	4.2
Measured transverse shunt impedance, R_⊥(MΩ/m)	7.1
Simulated transverse shunt impedance, R_0⊥(MΩ/m)	7.4

Fig. 12

(Color online) Projection of bunches without and with phase offset during calibration. The blue solid line is the outline of the bunch that enters the deflecting cavity at zero phase. The green dotted line is the outline of a bunch that enters the cavity at a 1° phase offset. The distance between the bunch centers in the y direction is 4.4 mm.

6 Conclusion

This paper presents the design, RF testing, and bunch-length measurement of a 2856-MHz, π-mode, 7-cell SDC in the TTX platform. The theory of the SDC and its bunch-length measurement and calibration have been reviewed. Compared with the TDS, the SDC is more compact, with its length only one-fifth that of the traveling wave, in our case. A simple and quick method was used to optimize the multicell SDC working in π mode. The transverse shunt impedance per meter was optimized by adjusting the end-cell length, which can guide the design of a multicell deflecting cavity. After fabrication and tuning, the parameters of the cavity correspond well to the simulation results in the HFSS.

This cavity was installed in a TTX and provided a deflecting voltage of 4.2 MV with an input power of 2.5 MW. Bunch-length diagnosis of electron beams with an energy of 39 MeV was performed. In the near future, this cavity will be used for bunch-length measurement in a new beamline in Tsinghua, which will generate terahertz radiation with a laser-modulated electron bunch for research.

References

[1]

C. Tang, W. Huang, R. Li et al.,

Tsinghua Thomson scattering X-ray source

. Nucl. Instrum. Meth. A 608, S70-S74 (2009). doi: 10.1016/j.nima.2009.05.088